Why is my Fisher and Paykel not spinning?

Check the amount of detergent used, reduce if necessary. Ensure a detergent designed for use in a front loader is used. Straighten any kinks along the hose that drains water from your washer. If the kinks return, you may need to replace the hose.

How do I reset my Fisher and Paykel top loader washing machine?

You can reset your washer to the default settings it left the factory with:

1. Turn the dial to select ‘Spin’.
2. Touch and hold the ‘Delay Start’ ‘More’ , the ‘Delay Start’ ‘Less’ and ‘Options’ buttons together for 3 seconds.
3. Your washer will now be reset to the default settings.

Is there a reset button on a Fisher and Paykel washing machine?

Touch and hold the ‘Start/Pause’ button for 3 seconds to reset the factory settings.

Why isn’t my washing machine spinning?

Normally, your washing machine won’t go into a spin cycle until it’s been drained. The drainage hose may become clogged with debris from your clothing, or it could be kinked. If the hose is kinked or crushed, it will likely need to be replaced.

Why is my Fisher and Paykel washing machine not working?

Switch the power off at the socket, wait 60 seconds and switch on again (this may reset your washer). Either test the socket by plugging in a different appliance, or by plugging your washer into a different power socket. Keylock mode may be activated. Try holding down the POWER button for 2 -3 seconds.

How do I know if my washing machine agitator is bad?

When the top half of the agitator in a top-load washer doesn’t agitate as it should, or if you can turn the agitator back and forth freely, it could mean the agitator dogs are worn out.

Can you use a washer without the agitator?

A washer without an agitator tends to use less water and energy. They have a larger capacity because the spindle of the bulky agitator doesn’t take up space. An alternative impeller mechanism that is installed in the middle of the washer basin is effective in cleaning clothes.

How do I reset my Fisher and Paykel?

Reset Procedures for the Fisher & Paykel Dishwasher

1. Press and hold the button decorated with the key and lock image for five seconds.
2. Press the power button to turn off power to the Fisher & Paykel dishwasher.
3. Wait a few minutes and then press the power button to restore power.

Does Fisher and Paykel washing machine have a fuse?

There are 2 fuses on the board (see pic), one of 1.6A and the other of 4A, both type ‘T’ (slow-blow).

Where is the agitator on a Maytag washer?

Your machine may hold the agitator in position via a threaded bolt on the top of the shaft of the transmission, under the dispenser for the fabric softener or under the top cover. Or there may be a little screw connecting the agitator’s barrel to the transmission shaft, right above the base.

How do you change the agitator on a whirlpool washing machine?

Unplug the washer and take the cover off the fabric softener dispenser. There will be a bolt there holding the top half of the agitator on. Undo the bolt, take off the agitator’s top portion, and look to see if the agitator cogs have worn smooth and need replacement.

Why won’t my top-load washer agitate?

If you have a top-load washer that won’t agitate and you’ve been hearing a vibration, there may be a problem with the direct drive motor coupling between the transmission and the motor. This coupling is two drive forks made of plastic, one attached to the shaft of the drive motor, and one attached to the input shaft of the transmission.

How do I know if my agitator spline is worn down?

This is important because you can tell if the spline is damaged when the bottom part of a dual-action agitator or the whole of a single-action agitator fails to move while the machine is on a wash cycle. The spline is worn down if the agitator can be turned with your hands around the shaft: remember it is designed to be locked into place.